You were doing skids and over heated it didn't Ya!
I think you might be able to blame the sun on that one though.
mrfxit,
Mar 16, 2:45pm
Who ME, doing skids. NEVER ;-) Tyre survived ok
intrade,
Mar 16, 2:50pm
yea thats todays plastic for you. i even seen cv boots rott off the joint at naigbours car she hardly drives it and it was mentionedon wof sheet so i looked at it and it was split and hanging almost off the shaft. You will need steel rims as todays plastic is crap only as cheap as possibile not like the early days of plastic or even bakelite that stuff is still like new 70 years later.
daryl14,
Mar 16, 2:58pm
You still got toe rags doing burnouts up your street!
mrfxit,
Mar 16, 3:08pm
Seem to have run out of cash for tyres, appear to be content recently with boosting up & down the street. Been a few towed this year from down that end of the street with blown motors
daryl14,
Mar 16, 3:12pm
I reckon you'd get away with just pouring some petrol down the back edge of the bonnet and lighting it up. It would just look like an internal fuel leak had occurred, wouldn't it!
We had some yoofs evicted out of our street last year. Nice and quiet now.
tmenz,
Mar 16, 3:26pm
Were you giving someone a lift! Were you off your trolley at the time! Are you weally busted up about it!
mrfxit,
Mar 16, 3:32pm
No one gets to ride my trolley ;-)~ Does a coffee instead of a bourbon count as being off my trolley More "busted" up about replacing the tube rather then the mag
robbo36,
Mar 16, 3:59pm
Replace them both with solid tyre/wheels, they don't go bang!
mrfxit,
Mar 16, 4:15pm
Nah, thats what used to be on there & they were too hard on the suspension (me)
kevymtnz,
Mar 16, 4:17pm
lol my wheel barrow decided to have a blowout at 2am woke me up instantly
socram,
Mar 16, 4:18pm
Fred Flintstone never had that problem. I'll bet.Such is progress.
mrfxit,
Mar 16, 4:19pm
Heck yes, just imagine the mess & heap of explaining about how that load of new computers / parts got dumped on the tarseal
clark20,
Mar 16, 4:21pm
Did you exceed the speed rating!
supernova2,
Mar 16, 4:43pm
To me that looks as if its had an aftermarket axle assembly fitted.I hope you have the cert somewhere otherwise Johnny will be after you.
mrfxit,
Mar 16, 4:49pm
DANG IT . got me on that (Just as well john & his sidekick wasn't looking)
mrfxit,
Mar 16, 4:51pm
Nah, was parked up at that stage, looks like it will be for a bit longer now
chevcamaro,
Mar 17, 3:05am
a unimagcycle lol
lookoutas,
Mar 17, 3:52am
Same happened to me. Only I got so pissed with them going flat all the time, that I'd pumped the crap out of them, and left it in a hot shed. Replaced them with solid lawnmower wheels. Bastards don't go flat now!
intrade,
Mar 17, 11:17am
umm i just woke up to a bang lol same happend to my steel rim ones big bang the rim got bentand the tube cut up on one side will need to do something else also sooner or later now.
supernova2,
Mar 17, 11:28pm
Wot sort of pressure are you guys running these things at!300psi or something!
mrfxit,
Mar 17, 11:47pm
LOL nah, I suspect mine was up around 35psi that day. it's the Chinese tubes that give way & take out the thin steel or plastic rims
lookoutas,
Mar 17, 11:52pm
When ya get pissed-off enough - that's possible! "Go flat now ya bastard"
mrfxit,
Mar 18, 1:55am
LMAO . "LIKE" +1
OMG did I just say "like" ha ha ha he he he ha ha ha he ha
intrade,
Mar 18, 2:00am
i had 4 bar im my one the rim is fine the sidewall cracked and then the hose blew out thru that. it was 5 year old however and from supersheep for 35$, it was definetly overinflated i let some air out of the other, I was thinking if i pump it that hard then it be ok in 2 month when i use it again lol
Since the public registrations are closed, you must have an invite from a current member to be able to register and post in this thread.
Have an account? Login here.