Motoring Message Board Page 286 / 1068
| Topic | Replies | Last post |
|---|---|---|
|
West Auckland WOF - where to go? Looking for a WOF place in west auckland that isn't over the top strict, got an older car with some rust etc, which will probably fail anyway, but hoping for someone more realistic than the likes of vtnz. can anyone recomend anyone/anywhere! |
33 | |
|
Removing back seats - is this ok? So I want to take the back seats out of my car, as well as basically all the interior plastic, so its pretty much bare metal from the front seats back. Is this legal! |
7 | |
|
I turn car off and it carries on. .only a couple of seconds but its splurts to a rough stop.1992 mitsi l200 ute.any ideas whats causing this rough shutdown! |
18 | |
|
Mazda Axela 23s 2004.Advice Looking at this one on the weekend,silver hatchback, done 82k.listed on here.any input would be greatly appreciated.Cheers.-.Bren |
11 | |
|
Springs in hamilton for reel mower does any one know where in the tron know where a parts place is need one a about 40 mil by 10 strong as to hold up reel |
1 | |
|
Rev gauge wiring? hi all i have a rev gauge because my car is to old to have its own! 1981 i have red,black,white,green. i know red is battery and black is earth but which colour goes to neg on the coil [green/white]and what do you do with the other one! |
3 | |
|
Toyota recond short block Anybody purchased a corolla 1500 5A-FE short block recently, If you have what was the cost! just a rough idea would help. Cheers |
2 | |
|
What brand of tools are good Going out today to grab some new tools, a socket set and a spanner set. Can anyone recommend any good brands of warn me of brands to stay away from! |
25 | |
|
Nissan silvia having trouble finding nissan wreakers, could somebody please leave some phone numbers if you know of any. witht the company name etc. i need a passenger headlight for a s13 silvia (square type) |
5 | |
|
Is this a Joke? A Head specialist says he can acid dip my head for 50 bucks no worries, but then reckons that the valve seat will then have to be replaced and quoted $800+gst just for a 6 cylinder 12 valve cylinder head! im not sure this is right, but i have been quoted ... |
33 | |
|
At least they got the engine right. http://www.trademe.co.nz/Trade-Me-Motors/Specialist-cars/Hot-rods/auction-367301381.htm |
3 | |
|
Cheap WOF in Christchurch? Anybody know any open Saturdays! |
6 | |
|
Good stuff http://www.stuff.co.nz/national/crime/4867479/U-turn-cop-charged-over-death |
2 | |
|
Geez, someone got a bargain 366804763 |
11 | |
|
Air Compressor not working Update with photos Hey Guys, Reciently posted a thread with one side of my compressor blowing out the intake instead of sucking. Here is pick with head off. Anyone in the know tell me if it looks ok (if you can tell) pretty crap photos. Valves are metal.That tube that attac... |
7 | |
|
"Parking Enforcement Services breach notice" The member deleted this message. |
39 | |
|
Was in a near miss case of 'tie your load' down yesterday morning, had to go to a hospital appointment in town, got stuck in a traffic jam going up a long steep hill with a little delivery truck infront of us, guy kept doing these really bad hill starts with us thinking he was going to slip back and hi... |
9 | |
|
Start your own web site deal Looks bluddy good to me!.and the stuff the guy wrote.whatever that was. http://www.trademe.co.nz/Business-farming-industry/Businesses-for-sale/Internet-technology/auction-366244584.htm |
3 | |
|
Floaties in the radiator went to flush my radiator yesterday, and there was a mixture of coolant and rusty water, i wasnt overly concerned until there were small bits of brown crap floating in the water. upon further inspection its very small lumps of oil. so my question is, how ... |
7 | |
|
Isuzu Bighorn 4JB1 2.8 Smokes when Cold Start I have replaced the 2.8 4jb1 motor in my Bighorn Lotus Turbo and intercooler, the owner of the donor truck that I got the motor from said it smoked up real bad on a cold start, smoked and smelled like diesel for a bout 2 or 3 minutes. Now the mechanics to... |
11 | |
|
Go kart sprockets & clutch i bought my son(7)a go kartit has a 190cc 4 stroke(honda copy ) motor and centrifugal clutch.10 tclutch and 56 tooth drive with38 cm diawheels. in theory it has a top speed of approx 48 kmph at 3500rpm, i would like to gear it down so it has a lower top s... |
7 | |
|
FIAT PUNTO 2001 Just drove one ----------------- should of driven one last week would not of bought sentra, will need to revisit! |
36 | |
|
GM ZZ454 crate motor Anyone run one of these motors in your Chev before and how have you found them! Very interested in one |
3 | |
|
I'm importing a car from Japan. any advise? I'm importing a year 2000 JZX110 Toyota Mark II IR-V (Turbo 1jzgte). Just want to point out that I've done my research and just wanna ask for opinions from a different perspective (Buyers/Importers). I rang the Jappas up and they told me that the ... |
18 | |
|
Dyna vs delta I would think that the build quality between diahatsu and Toyota would be the main differance, I don't think diahatsu was. Bought out be Toyota till later and diahatsu most likely were using worse metals |
1 |