valve tag
| Topic | Replies | Last post |
|---|---|---|
|
Do I have a crook PCV valve! 2002, 180kms. Audi 3.0ltr petrol V6: surging at idle. The surge is rhythmic, varies by 200-300rpm, only seems present when the engine is warm, and can be replicated right up to 1,500RPM. The surge gets worse if the oil filler cap is removed. Does this imp... |
11 | |
|
Opel Vectra 92 2ltr (Bake pressure Valve) Brake Pressure valve can anyone tell me where this is located! it failed a wof due to bake imbalance I got him to find the course p/valve been stuffed.mechanic says $280 new or 170 2nd hand but he said I have x2 valves non abs help please.I want to know w... |
3 | |
|
Proportioning Valve Replacement what sort of cost am i looking at to get this done! i have a 2000 daewoo and im going to take it to midas on monday. sorry its the rear Brake Proportioning Valve. tia |
6 | |
|
Where would I get an ISC valve from (94 MItsi) Apparently my car needs a new one of these, Repco said they dont deal with these products, BNT told me they don't either, and Mitsi said the can only get genuine for around $300+GST, we only have one wreckers here that I know of and they dont have any... |
1 | |
|
Ford telstar 1988 2lt 12 valve, idle issues Can anyone help, have a really high idle and automatic choke appears to stay on even when engine has warmed up. |
3 | |
|
Plugging motorcycle valve? Hi guys, i am wanting to carry out this on my ninja due to too much popping and banging on deceleration.But i need these little plastic caps to do the job properly. any idea of where i can find these!http://asianconnection71.com/0728PAIRValve1.jpg iv had ... |
13 | |
|
Recirculating blow off valve Hi guys, got a car that came with a recirc bov in the back seat haha. Just wondering if it will do any damage, or affect the way it works, if I hook it up but not plumb it back into the air intake! The air intake doesn't have a phlange for the hose yo... |
6 | |
|
One way air valve where can I get or what could I use as a one way valve for air! it needs to let enough air through to an idle control valve to control idle speed on my motor. When it hits boost (supercharger) and the manifold pressure comes up, it needs to close so the b... |
7 | |
|
Valve stem seals nissan avenir. So my Avenir has been painfully difficult to start in the mornings. Mechanics replaced the thermo sensor, and this has made the idle better.-But still takes 3 or 4 goes to start it in the morning.Mechanics took it to an auto sparky to run diagnostics, and... |
5 | |
|
Need valve tool and grinding paste I'm looking for one of those sticks with suckers on and coarse/fine paste to lap in the valves on my bike. Has anyone seen that stuff for sale anywhere! Can't remember it being at Supercheap etc! Cheers. |
5 | |
|
Burnt exhaust valve on 03 XR 8! Anyone had similar drama's with their's!F***** me right off for a 116km car.Bought at 78km. |
26 | |
|
Valve springs, best option. Just found a broken spring, was wondering what the problem was, have been right through the carbs, fuel pump, dizzy, electrics etc. Decided to finally lift the rocker cover and there it was, no 3 inlet, outer coil! As far as I can see, the coil is the sam... |
2 | |
|
Tyre valve removal key/tool where would I get one, any ideas. Cheers |
5 | |
|
Valve Clearances Hi there guys, another question, I need to adjust the valves on my 1977 Triumph 2500tc, but, weirdly. My haynes manual does not state the valve clearances, Now i have found a source online that states that the valve clearance should be 0.25mm when cold on... |
40 | |
|
1994 mazda lantis egr valve I have searched the net endlessly and can not find any help in locating the egr valve for my 1994 mazda lantis 1800 4 cylinder. can any one help PLEASE |
21 | |
|
How to remove bias valve I am trying to undo the brake lines from bias valve as it is leaking but the 10mm open spanner just wants to splay and round off heads of nuts, tried slotting the ring end on the spanner to slip over brake line then onto nut but still no joy, tried 4 diff... |
13 | |
|
Honda Experts, can ya disable the egr valve setup hey, we have innova that runs the 2 litre F20 SOHC injected motor (non vtec). I suspect the egr ports are partially blocked on the inlet manifold. It's a pig of a job to access the ports to clean them. What I need to know, Can you simply disable the E... |
3 | |
|
Valve stem seals What model! 8 valve or a 12 valve or a 16 valve engine, some are a bit differcult to do without taking the head off. |
2 | |
|
Worn valve lifters In a crdi single-ohc engine would worn valve lifters(cam followers) be likely to cause upper engine noise, regardless of engine speed? Am I correct to believe that "valve lifters" is just another name for "cam followers"? |
21 | |
|
Wolf valve grinder rubber belts I have an old Wolf Valve Re facer (model 8004?) The rubber drive belts have perished and broke. They are just flat rubber belts. The short one being 300mm (circumference) x 20mm x 3mm. The long one is 700mm circumference. I’ve tried a |
12 | |
|
Broken brake bleed valve. One of the brake bleed screws on the caravan has broken off. How can i get the thing out so I can put a new one in. ? |
6 | |
|
Additive for valve stem seals I have an engine that has sat for a couple years, Its a SR20VE. It goes like stink but the valve stem seals are obviously a bit dry presumably from the storage period. Are there any additives you can put in the oil to help reduce the oil going down the st... |
8 | |
|
EGR valve /manifold cleaning Vito merc van has sporadic loss of turbo straight after a strange 'creaking ' noise behind the dash at glove box area, after about 5 seconds it takes off as usual? Could it be just a matter of course to clean it all out, cost at garage? Cheers. |
18 | |
|
Corolla BZ 20 valve idling at 1500rpm To high? I'm sure it is supposed to be around 800 to 1000? Whats the fix? Also still getting a flat spot on acceleration sometimes. Put fuel cleaner and injector cleaner through but its only improved it a bit. Put.ting the Ac on brings the revs down |
6 | |
|
Blanking EGR Valve on 4g64 GDI Hi there, I have read that blanking of the EGR Valve on 4g64 GDI with old outlet manifold gasket will solve some issues of inlet manifold getting coked up with carbon. Any thoughts |
1 | |
|
Blanking EGR Valve on 4g64 GDI Hi there, I have read that blanking of the EGR Valve on 4g64 GDI with old outlet manifold gasket will solve some issues of inlet manifold getting coked up with carbon. Any thoughts |
19 | |
|
Blow off valve? Excuse my ignorance Definitely a blow off valve. |
21 | |
|
Valve in block engine what car make is this Cylinder Head for ?https://trademe.tmcdn.co.nz/p-hotoserver/full/856109244.jpg https://trademe.tmcdn.co.nz/photoserver/full |
16 | |
|
07 Triton 3.2L EGR Valve Have had the Manifold cleaned due to carbon build up as the EGR valve through out a code causing check engine light. code was reset but shortly after it has come back on again, amused the valve is gone so took it to the dealer to confirm and yes they reco... |
40 | |
|
Where to replace Oxy/acet valve? The square key in the valve of the oxy bottle sheared off. So cant open or close the valve. Where do i go to have the valve replaced or repaired? Supagas? I guess the bottle will need to be retested too? Any idea how much $$? Anyone know? Thanks |
8 | |
|
Valve seat recession in 1kz engine hi would overfueling cause valve seat recession |
10 | |
|
2008 VFR800 Valve Check Hi folks, I've got a 2008 VFR800 that is nearing the big 25,000kms service, and part of that involves a very very very time consuming (7 - 10hr+) inspection / adjustment of the valves. This is going to cost a fair bit, which is OK, but does anyone know of... |
7 | |
|
Would TH400 Full Manual Valve Body handle Circuit Racing , Targa or would it be to much for such a set up ? Powered by a 300hp at the wheels 350 chev. Cheers |
17 | |
|
Toyota Egr valve cooler The local courier is having trouble with her 2009 Hiace Diesel,the engine light comes on and the engine drops all power.The van has gone to a local Toyota agent and apparently the fault is in the EGR valve cooler.which gets sooted up ! Toyota have apparen... |
21 | |
|
Turbo question. We have a subaru imprezza if has just started making a blow off valve sound and boosting real hard it does not h We have a subaru imprezza. If has just started making a blow off valve sound and boosting real hard. It does not have a blow off valve. Is this going to cost us! Is it the boost controller! |
6 | |
|
Koenigsegg Free-Valve-Technic http://teamspeed.com/forums/supercars/78595-koenigsegg-cargine-free-valve-technology-described.html |
4 | |
|
Brake proportioning valve. anyone know where it is on a 1996 nissan stagea with abs. 40% imbalance from left to right |
13 | |
|
Co2 gas valve prob I have a full 2.m3 gas bottle which i just got tested and had a valve put on.The valve thats been put on has a small out let 7 8 gas thread not a 1/2but my regulator is a standard mig one that goes into a argon sheild. can any body tell me where i can get... |
7 | |
|
Valve clearances for 1985 honda city? searching for the intake and exhaust clearances on a 1985 honda city. seems to be hard to find. Any help appreciated |
12 | |
|
Ford transit EGR valve fault, Gidday, my 04 2.4td transit has been scanned and fault is EGR valve. This cuts out the turbo till engine warms a little, then flick key off then back on while driving. This resets the fault, Glow light stops flashing and boost is back.But it is a little a... |
15 | |
|
1993 Toyota Carina ST190 proportion valve location Every time I take this car for a WOF it get rejected by rear brake imbalance.I can usually get it through with brake adjustment - but not this time.Mechanic at VTNZ said it will be the proportioning valve which he thought was on the fire wall.I have had a... |
11 | |
|
RApir costs - Coolant pipe / cold start valve Hi all. An associate of mine bought a 96 Imprezza HX. Ran fine for the last few months, then it started steaming from the engine. They took it in for repair and could see that there was some sort of coolant piping problem. Decides to check out the breaks ... |
6 | |
|
Axial spool control valve Just wondering if it is the control valve pin that moves the spool in these assembles. |
4 | |
|
RB20 E single cam. Can valve stem seals and a rattley tappit be replaced without taking head off thanks can valve stem seals and a rattley tappit be replaced without taking head off! thanks. |
7 | |
|
What can cause a bent valve in the engine. just one of those things,or something we have possibly done! thanks :) |
44 | |
|
Can 4a-fe valve stem guides and seals be replaced WITHOUT taking head off . simple yes or no please All answers will be taken into account . Going through 4 litres of oil in a month (i hasten to add i do about 500-600kms per week) No oil burning before 3 - 3500 revs - just over that and on start up (clea... |
6 | |
|
Does my 88mitsi have a pcv valve? my 88 mitsi mirage let me down a few months back(lost all its power) but i nursed it to a mechanic. He popped the air filter cover off and found it chockka with oil. I told him the guy from oil changers reckoned it was a dodgy PCV valve but the mechanic s... |
8 | |
|
Egr Valve \i am wondering if some one can tell me if this vehicle has an EGR valve and if so where it is located! It is a 1993 Opel Astra F 2 litre sedan. here is a photo of the engine bay if some one can point me in the right direction. I am by now means a mechani... |
4 | |
|
Ford Courier Valve clearances What is the valve clearances for a 2004 Ford courier xlx,2x4. 2.5l intercooled turbo! |
2 | |
|
Help Sealco Spring Brake Control Valve SPRING hubbys redone the entire truck but now we cant work out which way the spring goes back on the knob inside the truck cab! anyone got one they can take a pic of for us! |
1 | |
|
5.7L oldsmobile v8 diesel valve clearances! anyone able to tell me the valve clearances for these! maybe someone has an old manual lying around! |
1 | |
|
Valve cover gaskit Hi all, I'm looking for a new gasket for my valve cover. I'm planning on taking the valve cover off so while I'm there I might as well change the gasket. I drive a Mitsubishi Evolution 6, so it's a 4G63 motor. Where can I go to get a new o... |
7 |